IFCS-60W Intelligent Dehumidifier Plastic Case Dehumidifier

I. Product Profile

Intelligent dehumidification device is a semiconductor refrigeration dehumidification method, the humid air in the confined space is actively sucked into the dehumidification duct under the action of the fan, and the water vapor in the air condenses into water after passing through the semiconductor refrigeration mechanism, and then discharged out of the cabinet through the conduit pipe, and it can achieve a very good effect of dehumidification. By reducing the water content in the air, the relative humidity and absolute humidity drop at the same time, almost no increase in temperature, no negative impact of temperature difference, fundamentally eliminating or reducing the occurrence of accidents, and will not be accelerated due to high temperatures in the cabinet devices and cabinet aging. Intelligent dehumidification device to passively prevent condensation mode, changed to actively guide the condensation, effectively preventing the cabinet equipment aging, insulation strength reduction, the second terminal breakdown, material mold and steel structural components corrosion and other security risks, to ensure the safe operation of the power grid.

Condensation inside the equipment caused by creepage, flashover accidents, generally occur in the following situations: First, high humidity in the region, the weather temperature changes, the bottom of the switchgear wet, and some cable trench and even water; second, there are switchgear in the basement, high humidity, the temperature inside the cabinet, especially close to the ground temperature is lower than the ambient temperature; third, there are equipment in a temporary shutdown, the electrical cabinet, a small ambient temperature than the Around the ambient temperature is low, in its surface is very easy to form condensation, in this case, once the power put into operation, the accident occurred. In order to ensure the safe operation of the power grid system, the long life of electrical equipment, safe and effective use of the power system on the cabinet moisture, anti-condensation dew put forward higher requirements.

II. Scope of application

1, GIS control cabinet, high and low voltage switchgear, ring network cabinet, outdoor terminal box, mechanical control cabinet, box-type substation, dry-type substation and other electrical equipment;

2, integrated circuits, silicon crystals, liquid crystal devices, ceramic devices, resistive components, active components, connectors, SMD devices, CPU, computer boards and cards moisture storage;

3. Moisture-proof management of physical and chemical instruments, experimental materials, insulating materials, and moisture-proof storage of chemicals, drugs, food, fibers, and biological agents.

III. Product characteristics

1、Small size, light weight, easy and quick installation;

2, automatic operation and manual dehumidification function switching, temperature start value and dehumidification start value adjustable;

3, dehumidification duct active condensation, discharge gas heating and humidity reduction, effectively achieving a comprehensive treatment of moisture and dehumidification of the electrical cabinet confined space;

4, humidity, temperature sensor 24 hours real-time sampling, beyond the set start value automatically lead to condensation;

5, humidity, temperature settings with memory function, will not disappear because of stopping the boot;

6, fault display function, can quickly find the fault point to ensure normal operation;

7、Using special moisture-proof components to ensure normal operation in humid environment;

8, the use of shielding isolation technology, in line with the GB / T17626-2018 of the level 3 standard, to ensure that can work under strong electromagnetic fields;

9, dehumidification lead to condensation pipeline, can lead to condensation after the water discharged out of the cabinet, but also can be used to collect liquid storage bag outside the cabinet.

IV. Functional features

1, temperature and humidity monitoring and display function, dehumidification / low temperature threshold can be set;

2、Rapidly reduce the humidity in the switchgear cabinet, and the water is directly discharged out of the cabinet;

3、Heating output contact: one way passive contact output can be connected with external heater to assist dehumidification.

4, dehumidification work control mode: manual / automatic;

5, communication function and dehumidification fault alarm function.

V. Technical parameters

VI. Principle of operation

Intelligent dehumidification device consists of power supply system, air supply system, semiconductor cooler, temperature and humidity detection and control circuit, heating circuit, wireless module and thermal insulation and drainage piping.

1Principle of Dehumidification

When the humid air by the fan inhalation, through the specially designed duct flow, first by the semiconductor cooler cooling condensation, cooler condensation under the action of gravity drops into the water tank, and then by the heat preservation guide pipe out of the cabinet. In the set start-up value after full circulation dehumidification, so that the cabinet air humidity down to below the dew point, to complete the entire moisture induced condensation heating process. At the same time, the intelligent dehumidification device signal acquisition sensor external, real-time accurate collection of the real humidity inside the cabinet, to ensure that the intelligent dehumidification device in the cabinet will reach the condensation conditions in advance to start dehumidification.

2Low-temperature heating function

When the box temperature is lower than the set start value, the dehumidification device to start the internal heater circuit (heater external, power can be connected to 50 ~ 500W), until the box temperature rises to the set start value plus 5 ℃, the heater circuit to stop working.

3,RS485 communication function

When the dehumidifying device with RS485 communication function receives the data from the host computer, it will analyze the data and immediately reply the data to the host computer, and a maximum of 200 units can be connected to one host computer (a 120-ohm load resistor is recommended to be connected between A and B on the host computer side).

VII. Display notes

After power on, the dehumidification device enters the self-test state, after the self-test is completed, the humidity value is displayed on the left side, and the temperature value is displayed on the right side.

Size: wide 100mm*your (honorific) 170mm*厚 74mm

VIII. Operating instructions

1, manual/confirmation: in the display interface press the key dehumidifier to start manual dehumidification, at the same time the device on the load light, dehumidification light on at the same time. Press the key again to cancel the manual mode, the dehumidifier stops working. Load light/dehumidifying light goes out at the same time.

2, refrigeration plate temperature: in the display interface, press the key to view the refrigeration plate temperature. When the refrigeration plate temperature reaches the set value after the dehumidifier stops working to start defrosting mode, to be the refrigeration plate temperature returns to a certain temperature before starting the work mode.

3、Setting parameter mode: Press the setup button to enter the setup interface and press the up and down keys to flip to select the parameters that need to be configured. Then press the confirmation key to enter the function setting interface, after entering the setting interface, the following values will flash, and then press the up and down keys to adjust its parameter values. After the parameter setting is completed, press the exit key to return to the main interface, and the parameter will be saved automatically. The function codes are defined as follows:

IX. Wiring Diagram

Live Cases:

Before dehumidification - water beads visibly on cabinet walls

After dehumidification - no water droplets on cabinet walls